ASTM A240 Type 2507 Plate & Coil suppliers in India
2507 Super Duplex Sheet
SAF 2507 Stainless Steel Plate
Check newly updated Super Duplex 2507 Cold Rolled Plate price list in Mumbai
Table of Content
2507 Super Duplex Sheet Specification Schedule
Super Duplex 2507 Plate StandardsASTM ASME: A240 - UNS S32750
EURONORM: 1.4410 - X2 Cr Ni MoN 25.7.4
AFNOR: Z3 CN 25.06 Az
| Material | 2507 Super Duplex Sheet & 2507 Super Duplex Plate |
|---|---|
| Specification | ASTM A240 and ASME SA240 |
| Tolerances of Width and thickness | European Standards 10258 European Standards 10088 European Standards 10151 |
| Standard Sizes in MM | 1000*2000, 1220*2440, 1500*3000, 2000*2000, 2000*4000 |
| Thickness in Mm | 0.1 to 100 |
| Width in Mm | 10 To 2500 |
| Length in Meter | 2, 2.44, 3, or as per client required |
| Finish | No.4, brush, Hot rolled, 2B, BA, 8K, SATIN, 2D, hairline, NO(8), 1D, No.1 finish, Cold rolled, satin, mirror |
| Hardness | Half Hard, Spring Hard Quarter Hard, Hard, Soft Super Duplex Plate Supplier |
| Manufacturers | TISCO, Jindal, JPOSCO, Alloys, ZPSS, Outokumpu, BAOSTEEL, JISCO, Shah Sail, LISCO |
| form of | Flats, Rolling Sheet, sheared, soft annealed, tread plate, Coils, descaled, Rolling Plate, Clad Plate, Plate, annealed, Strip, Flat Shim, Checker Plate, Sheet, Blank, Plain Sheet, Flat Sheet, Shim Sheet, Rolls, Foils Super Duplex Plate Supplier and Manufacturer |
| Distributor and Suppliers Located in Following locations | Ahmedabad, New Delhi, Istanbul, Gujarat, Kolkata, Bogota, Surat, Vadodara, Ahvaz, Janeiro, Santiago, Tehran, Howrah, Melbourne, Noida, Port of Spain, Perth, Gurgaon, Dammam, Manama, Hyderabad, Baroda, Indore, Mexico, Ernakulam, Coimbatore, Lagos, Chennai, Kanpur, Rajkot, Thiruvananthapuram, Jamshedpur, Abu Dhabi, Calgary, Pimpri Chinchwad, Courbevoie, Bengaluru, India, Karachi, Ankara, London, Sydney, Ludhiana, Mumbai, Kuwait, Ludhiana, Riyadh, Bangalore, Muscat, Caracas, Khobar, Ranchi, Nagpur, Gimhae si, Montreal |
2507 Super Duplex Plate Hot forming
2507 should be hot worked between 1875°F & 2250°F. This should be followed by a solution anneal at 1925°F minimum and a rapid air or water quench.
Duplex 2507 Plate Cold Forming
Many of the Super Duplex stainless steel forming methods can be used for cold working 2507.
Most Famous Types Of Super Duplex 2507 Plate
Best Price Guarantee with Mill Test Report of ASME SA 240 GR 2507 Coils
Super Duplex 2507 Plate
Duplex 2507 Sheet
SA 240 GR 2507 Sheet
ASTM A240 Type 2507 Plate
Duplex 2507 Plate
ASTM A240 Type 2507 Sheet
SA 240 GR 2507 Plate
Saf 2507 Perforated Plate
ASTM A240 Type 2507 Clad Plate
Duplex 2507 Stainless Steel Coils
SAF 2507 stainless steel plate
Hot rolled Saf 2507 Plate
Astm A240 Cold Rolled Duplex Steel 2507 F53 Sheet
Super Duplex 2507 Stainless Steel Plate Sheet
Super Duplex Saf 2507 Stainless Steel Sheet
Saf 2507 Super Duplex Stainless Steel Sheet
En Sus 2507 Super Duplex Stainless Steel Sheet
Saf 2507 Super Duplex Stainless Steel Perforated Metal Sheet
Super Duplex Hot Rolled Plate Saf 2507 Stainless Steel Sheet
Cold Rolled Ss Super Inox 2507 Duplex Stainless Steel Sheet
Astm A240 Super Duplex 2507 Steel Sheet
Super 2507 Duplex Stainless Steel Cold Rolled Sheet
2b Surface 2507 Super Duplex Stainless Steel Bbq Plate
2507 1.4410 Dss Super Duplex Stainless Steel Plate Sheet
SAF 2507 Stainless Steel Plate Sizes
| Surface finish | Thickness in MM | Width in Mm |
|---|---|---|
| 1D – Hot rolled, pickled, heat treated | 2.4 To 12.7 | maximum 2032 |
| 2R – Cold-rolled, bright annealed | 0.05–1.50 | 3 To 649 |
| 2E – Cold rolled, mechanically descaled, heat treated | 0.4 To 8.0 | maximum 2032 |
| 2H – Work hardened | 0.4 To 6.35 | maximum 1524 |
| 2B – Cold rolled, skin passed, heat treated, pickled | 0.25 To 8.0 | maximum 2032 |
| 2D – heat treated, Cold rolled, pickled | 0.4 To 6.35 | maximum 1524 |
| 2H – Work hardened | 0.05 To 1.50 | 3 To 630 |
| brushed, Polished | 0.5 To 4.0 | maximum 1524 |
| 2R – bright annealed, Cold rolled | 0.25 To 3.5 | maximum 1524 |
| Deco | 0.3 To 3.5 | maximum 1524 |
2507 Super Duplex Sheet Chemical Composition Chart
Check dimensions and price list of 2507 Super Duplex Hot Rolled Plate in India
Super Duplex 2507 Chemical Composition
| Carbon | Chromium | Nickel | Molybdenum | Nitrogen | Others |
|---|---|---|---|---|---|
| 0.020 | 25 | 7 | 4.0 | .27 | 0.001 |
Mechanical Characteristics of Super Duplex 2507 Plate
| Ultimate Tensile Strength, ksi | 116 minimum |
|---|---|
| Yield Strength 0.2%, ksi | 80 minimum |
| Yield Strength, ksi | 91 minimum |
| Elongation in % | 15 minimum |
| Hardness | 32 maximum |
| Impact Energy | 74 minimum |
ASTM A240 Type 2507 Duplex Plate Physical Properties
| Density | LBS per inch | 0.28 |
|---|---|---|
| Heat Capacity | Btu/lb/°F | 0.12 |
| Coeff of Thermal Expansion 68 to 212°F |
x10 To 6/°F | 7.2 |
| Modulus of Elasticity | psi=106 | 29 |
| Electrical Resistivity | W in * 10-6 | 31.5 |
| Thermal Conductivity | Btu/h feet °F | 8.7 |
Super Duplex 2507 Sheet Equivalent Material
PED approved Super Duplex Plate Supplier in Mumbai, SAF 2507 stainless steel sheet in various length and sizes
| STD | Uns | Werkstoff No |
| 2507 Plate and Sheet | S32750 / S32760 | 1.4410 |
Hot rolled Saf 2507 Plate Temperature Limit
| Temperature °F | RT | 32 | -4 | -40 |
|---|---|---|---|---|
| feet/ Lbs | 162 | 162 | 155 | 140 |
| Temperature °F | -76 | -112 | -148 | -320 |
| Feet/ Lbs | 110 | 44 | 30 | 7 |
Tensile Properties of SA 240 GR 2507 Shim Sheet
| Temperature in °F | 68 | 212 | 302 | 392 | 482 |
|---|---|---|---|---|---|
| Ultimate Tensile Strength | 116 | 101 | 98 | 95 | 94 |
| Yield Strength | 80 | 65 | 61 | 58 | 55 |
2507 F55 SS Rolling Sheet Toughness Values
| Temprature | -50°C | +20°C | -60°F | +70°F |
|---|---|---|---|---|
| Single | 75 J/Cm | 90 J/Cm | 54 feet/ lbs | 65 feet/ lbs |
| Average | 90 J/Cm | 150 J/Cm | 65 Feet/ Lbs | 87 Feet/ Lbs |
ASTM A240 Type 2507 Plate Hardness
| Average | HV10 180 To 230 | HB : 180To 230 | HRC : 20 |
If you searching a super duplex plate supplier from these places check our suppliers below
| We supplied to following Locations | Products |
| Indonesia, Philippines, Dammam -KSA, Belgium | Astm A240 Cold Rolled Duplex Steel 2507 F53 Sheet |
| France, Europe, Qatar, Thailand | Super Duplex 2507 Stainless Steel Plate Sheet |
| Germany, Thailand, Czechia, Malaysia | Super Duplex Saf 2507 Stainless Steel Sheet |
| USA, Bangladesh, Malaysia, Finland | Saf 2507 Super Duplex Stainless Steel Sheet |
| Saudi Arabia, Kuwait, South Africa, Brazil | En Sus 2507 Super Duplex Stainless Steel Sheet |
| South Africa, Hoston, Bahrain, Singapore | Saf 2507 Super Duplex Stainless Steel Perforated Metal Sheet |
| Australia, UK, Philippines, Nigeria | Super Duplex Hot Rolled Plate Saf 2507 Stainless Steel Sheet |
| Malaysia, Hong Kong, Oman, UAE | Cold Rolled Ss Super Inox 2507 Duplex Stainless Steel Sheet |
| Italy, Iran, Chile, Singapore | Astm A240 Super Duplex 2507 Steel Sheet |
| Turkey, Norway, United Arab Emirates, Malaysia | Super 2507 Duplex Stainless Steel Cold Rolled Sheet |
| Malaysia, Russia, Netherlands, Dubai | 2b Surface 2507 Super Duplex Stainless Steel Bbq Plate |
| Spain, Mexico, Egypt, UK | 2507 1.4410 Dss Super Duplex Stainless Steel Plate Sheet |
| Europe, Malaysia, United Kingdom -UK, UAE | 6mm Thick Super Duplex 2507 Stainless Steel Sheet |
| Canada, Poland, UK, Ellington -United States | 20mm Thick 2507 Super Duplex Stainless Steel Plate |
| Malaysia, Canada, Philippines, Singapore | 2507 Super Duplex Stainless Steel Checkered Sheet |
| Japan, Romania, Europe, Malaysia | 2b Hl No.4 Mirror Super Duplex Stainless Steel Sheet Plate |
| Colombia, Malaysia, Sweden, China | Super Duplex 2507 Stainless Steel Coil |
| Taiwan, Los Alamos -Mexico, Malaysia, Philippines | Super Duplex 2507 3mm Thick Stainless Steel Coil |
| South Korea, NY 12203 (USA), Singapore, Malaysia | Aisi Saf 2205 Duplex Stainless Steel Sheet Plate |
Ready Stock Of 25cr Super Duplex Polished sheet
| 2507 Hot rolled plate | Steel 2507 Rolling Sheet |
| Cold Rolled Saf 2507 Sheet | 2507 Checker Plate |
| Saf 2507 Shim Sheet | Steel 2507 Sheet |
| 2507 Corrugated Sheet | Saf 2507 Expanded Sheet |
| 2507 Rolls Sheet | 2507 Foil Rolls |
| Saf 2507 Chequered Plate | ASTM A240 Type 2507 Clad Plate |
| ASTM A240 Type 2507 Chequer Plate | 2507 Plate |
| Decorative 25cr Sheet | Mirror Finish 2507 Sheet |
| Avesta 2507 Strips | ASTM A240 Type 2507 Strips |
| 2507 Etching Sheet | 2507 Floor Sheet |
| 2507 Rolling Plate | 2507 Precision Strip |
| ASTM A240 Type 2507 Rolling Plate | ASTM A240 Type 2507 Precision Strip |
| Saf 2507 Strips | 2507 Stainless Steel Strips |
| F55 Sheet | F55 Diamond Plate |
| Saf 2507 Perforated Plate | 2507 Chequered Plate |
| Avesta 2507 Strips | 2507 Strips |
| 2507 Rolling Sheet | 2507 Rolling Sheet |
| ASTM A240 Type 2507 Rolling Sheet | 2507 F55 SS Rolling Sheet |
| 2507 Stainless Steel Rolling Sheet | saf 2507 stainless steel Rolling Sheet |
